Search Results
Filter Your Search
Category Group
Shop by Category
DUCT-3000 has a diameter of 3 in. The material is 65-45-12 Ductile Iron.
65-45-12 Ductile Iron is used to machine pistons, glands, caps, manifolds, rams, and valve bodies.
Ductile has higher machining speeds than steel and there is usually no need for deburring machined parts. The graphite flakes in the material act as a self-lubricant. Ductile can be flame or induction hardened as well as deep hardened.
Ductile bars are produced with sufficient stock on the outside diameter to ensure clean-up at the nominal dimension.
- Excellent machinability
- Optimal impact strengths
- Optimal fatigue properties
- Optimal electrical conductivity
- High magnetic permeability
Packages longer than 44 inches may have additional freight charges.
| 1-9 | $14.57 |
| 10-19 | $9.71 |
| 20-39 | $7.29 |
| 40+ | $6.47 |
HT-5000X4500 has a wall thickness of 0.25 in. The ID is 4.5 in and the OD is 5 in. The material is DOM 1026 Carbon Steel and has been stress-relieved and annealed.
Packages longer than 44 inches may have additional freight charges.
| 1-14 | $7.59 |
| 15-29 | $6.52 |
| 30-59 | $5.70 |
| 60-89 | $5.06 |
| 90+ | $4.56 |
Cast Iron Rod Clevis Mount with a 0.75 in – 16 TPI threaded end and a 0.75 in pin hole.
Clevis mounts help maintain alignment and protect the cylinder from side load. Mounts attach to threaded stud ends, pivot holes, or bolt holes on the cylinder. Can be used with hydraulic cylinders with standard bore sizes.
ALHT5250X5000 has a 0.125 in wall thickness. The ID is 5 in and the OD is 5.25 in. The material is 6063-T832 Aluminum.
Seamless extruded and cold-drawn. Hard coated on the ID which gives the aluminum tube a tough, abrasive-resitant surface.
6063-T832 Aluminum is used for pneumatic cylinder applications requiring very good corrosion resistance and/or light weight. Can also be used for low-pressure oil cylinders (250 psi or less).
- No machining required on the ID
- Seamless extruded and cold-drawn
- Hard coated interior
- Corrosion resistance
- Good weldability
Packages longer than 44 inches may have additional freight charges.
| 1-14 | $10.05 |
| 15-29 | $8.36 |
| 30-104 | $7.18 |
| 105+ | $5.58 |
25mm induction hardened chrome shafting. The base material is 1045/1050 Carbon Steel with 0.0005 in (0.0127mm minimum)-thick chrome plating and a case depth of 0.05 in (1.27 mm).
Induction Hardened Chrome is typically used in abrasive envrionments where the cylinder is exposed to rocks or heavy debris. Also used to machine clevis pins.
- Greater strength
- Better resistance to mechanical damage
Packages longer than 44 inches may have additional freight charges.
| 1-14 | $3.60 |
| 15-29 | $2.40 |
| 30-89 | $1.80 |
| 90-134 | $1.60 |
| 135+ | $1.44 |
MCPO-90 has a 90 mm diameter with Standard Chrome. The base material is 1045 Carbon Steel with a yield strength of 75,000 psi.
ASTM A108 is the most commonly used and economical grade of shafting for hydraulic cylinder components, blower shafts, and mandrels.
- Extremely smooth surface finish
- Excellent wear and corrosion resistance
- Good strength and impact properties
- Good machinability
- Reasonable weldability
- Fair response to normal heat treating and induction hardening practices
Packages longer than 44 inches may have additional freight charges.
| 1-29 | $22.40 |
| 30-59 | $16.02 |
| 60-119 | $12.43 |
| 120-287 | $11.20 |
| 288+ | $10.19 |
PS, 2.500 X 2.108 X 0.129 URE
RCW-90NBR-1-1/4×1-11/16×3/16
