Snap-in Wipers for Sale | CRC Distribution

Style ST-XL-PM wipers are molded from 55D polyester and are direct replacements for Style “ST”, “ST-XL” or “D” wipers. The polyester based material provides a tough abrasion resistant wiper for heavy contaminant environments. The outside diameter of the ring has a crush lip providing extra interference in the groove. A bead on the shoulder stops contaminates from entering through the groove. The inside diameter is ribbed to prevent pressure traps between the wiper and rod seal.

55D Durometer | Polyester Material | 4 in Nominal Inner Diameter

Features

• Molded from 55D polyester
• The outside diameter of the ring has a crush lip providing extra interference in the groove
• The inside diameter is ribbed to prevent pressure traps between the wiper and rod seal

The Hallite 820 single-lipped, snap-in rod wiper is designed to fit North American D-style housings and has been developed specifically for use in harsher environments with heavy contamination, such as in agriculture, off-highway, and forestry equipment. These wipers include a dust lip to prevent contaminates from entering through the groove. They also have a ribbed inside diameter for low friction operation and to prevent pressure traps between the wiper and rod seal.

93A Durometer | Urethane Material | 4 in Nominal Inner Diameter

Features

• Umbrella Wiper Technology™
• Reducing corrosion and preventing the ingress of contamination into the wiper housing groove and hydraulic cylinder gland which will result in increased system life.
• Moulded ribs on the internal diameter
• Easy to install without the use of special tooling
• Normally specified for harsh environments

AN wipers are ideal for light duty and pneumatic applications. Its main purpose is to prevent dirt and contaminants from entering the hydraulic or pneumatic systems.

AN wipers will retrofit into glands prescribed in MS-33675 for corresponding dash numbers of MS-28776.

• Flexible, snap-in design for easy installation into closed housings
• Low compression set

AN wipers are ideal for light duty and pneumatic applications. Its main purpose is to prevent dirt and contaminants from entering the hydraulic or pneumatic systems. Suffix “SH” designates slotted heel design, “V” designates fluorocarbon material, and “B” designates carboxilated nitrile material.

90A Durometer | Fluorocarbon Material | 4 in Nominal Inner Diameter

Features

• Flexible, snap-in design for easy installation into closed housings
• Low compression set

AN wipers are ideal for light duty and pneumatic applications. Its main purpose is to prevent dirt and contaminants from entering the hydraulic or pneumatic systems.

AN wipers will retrofit into glands prescribed in MS-33675 for corresponding dash numbers of MS-28776.

• Flexible, snap-in design for easy installation into closed housings
• Low compression set

Single-lipped, snap-in rod wiper is designed to fit D-style housings.

The ST-XLF wipers are designed to fit the standard ST wiper groove. These wipers include a dust lip to prevent contaminates from entering through the groove. They also have a ribbed inside diameter for low friction operation and to prevent pressure traps between the wiper and rod seal. Developed specifically for use in harsher environments with heavy contamination, such as in agriculture, off-highway, and forestry equipment.

Urethane Material | 2 in Nominal Inner Diameter

Features

• Precision trimmed wiping lip
• Retrofits most ‘D’ wiper housings
• Especially effective in vertically mounted cylinders
• Designed to follow the rod deflection caused by side loads
• Interchangeable with Hallite 520 wiper
• Sharp wiping lip scrapes heavy contamination from rod protecting sealing system
• Umbrella Wiper Technology™ protects housing from contamination and reduces moisture ingress

Suffix “V” designates fluorocarbon material,“N” designates nitrile material, and “HT” designates high temperature urethane.

90A Durometer | Urethane Material | 2 1/2 in Nominal Inner Diameter

Features

• Urethane Wiper Ring
• Min. Temperature Range of ‘-40 °F; N: -40°; V: -20 °F; HT: -40 °F
• Max. Temperature Range of 200 °F; N: 225 °F; V: 350 °F; HT: 225 °F

Suffix “V” designates fluorocarbon material,“N” designates nitrile material, and “HT” designates high temperature urethane.

90A Durometer | Urethane Material | 3 1/2 in Nominal Inner Diameter

Features

• Urethane Wiper Ring
• Min. Temperature Range of ‘-40 °F; N: -40°; V: -20 °F; HT: -40 °F
• Max. Temperature Range of 200 °F; N: 225 °F; V: 350 °F; HT: 225 °F

Suffix “V” designates fluorocarbon material,“N” designates nitrile material, and “HT” designates high temperature urethane.

90A Durometer | Urethane Material | 8 in Nominal Inner Diameter

Features

• Urethane Wiper Ring
• Min. Temperature Range of ‘-40 °F; N: -40°; V: -20 °F; HT: -40 °F
• Max. Temperature Range of 200 °F; N: 225 °F; V: 350 °F; HT: 225 °F

Suffix “N” designates nitrile material.

90A Durometer | Urethane Material | 1 1/2 in Nominal Inner Diameter

Features

• Urethane Wiper Ring
• Temperature range of -40 °F to 200 °F