Search Results

O-rings as elastic loops that seal static and dynamic applications. They are used to seal the space between cylinders, pistons, pipes and tubes and can be made from various materials.

70 Durometer | Buna-N Rubber Material | 7/8 in Nominal Inner Diameter | 1/16 in Cross Section | O-Ring

Features

• Pressure range varies according to diametral clearance
• Temperature range of -40 °F to -240 °F

ALHT4250X4000 has a 0.125 in wall thickness. The ID is 4 in and the OD is 4.25 in. The material is 6063-T832 Aluminum.

Seamless extruded and cold-drawn. Hard coated on the ID which gives the aluminum tube a tough, abrasive-resitant surface.

6063-T832 Aluminum is used for pneumatic cylinder applications requiring very good corrosion resistance and/or light weight. Can also be used for low-pressure oil cylinders (250 psi or less).

• No machining required on the ID
• Seamless extruded and cold-drawn
• Hard coated interior
• Corrosion resistance
• Good weldability

Packages longer than 44 inches may have additional freight charges.

CPO-0500 has a 0.5 in diameter with Standard Chrome. The base material is 1045 Carbon Steel with a yield strength of 75,000 psi.

ASTM A108 is the most commonly used and economical grade of shafting for hydraulic cylinder components, blower shafts, and mandrels.

• Extremely smooth surface finish
• Excellent wear and corrosion resistance
• Good strength and impact properties
• Good machinability
• Reasonable weldability
• Fair response to normal heat treating and induction hardening practices

Packages longer than 44 inches may have additional freight charges.

Parback® backup ring with a curved cross-section.

Parbaks are contoured on one face to minimize distortion of the o-ring when under pressure. Parbaks should be installed with the contoured face against the o-ring, but reversal does no harm.

90A Durometer | Buna-N Rubber Material | 3 1/4 in Nominal Inner Diameter | 1/8 in Cross Section | Backup Ring

Features

• Excellent extrusion resistance
• Easily stretched for installation
• Lubrication is enhanced by rubber which absorbs system fluid and does not plate out on rubbing surfaces

100mm induction hardened chrome shafting. The base material is 1045/1050 Carbon Steel with 0.0005 in (0.0127mm minimum)-thick chrome plating and a case depth of 0.05 in (1.27 mm).

Induction Hardened Chrome is typically used in abrasive envrionments where the cylinder is exposed to rocks or heavy debris. Also used to machine clevis pins.

• Greater strength
• Better resistance to mechanical damage

Packages longer than 44 inches may have additional freight charges.

60mm induction hardened chrome shafting. The base material is 1045/1050 Carbon Steel with 0.0005 in (0.0127mm minimum)-thick chrome plating and a case depth of 0.05 in (1.27 mm).

Induction Hardened Chrome is typically used in abrasive envrionments where the cylinder is exposed to rocks or heavy debris. Also used to machine clevis pins.

• Greater strength
• Better resistance to mechanical damage

Packages longer than 44 inches may have additional freight charges.

2.250 X 1.858 X 0.129 TFG

CIHT4236X4000 has a wall thickness of 0.118 in. The ID is 4 in and the OD is 4.236 in. The material is 1026 Carbon Steel with chrome plating on the Inside Surface.

Packages longer than 44 inches may have additional freight charges.

*
2 in Hot Finished 1018 Carbon Steel*
round bar. Material can be cut to any size.

Suitable for shafting and applications that do not require the greater strength of high carbon and alloy steels.

• Good case hardening properties
• Fair machinability
• Readily brazed and welded

Packages longer than 44 inches may have additional freight charges.

Suffix “V” designates fluorocarbon material,“N” designates nitrile material, and “HT” designates high temperature urethane.

90A Durometer | Urethane Material | 2 in Nominal Inner Diameter

Features

• Urethane Wiper Ring
• Min. Temperature Range of ‘-40 °F; N: -40°; V: -20 °F; HT: -40 °F
• Max. Temperature Range of 200 °F; N: 225 °F; V: 350 °F; HT: 225 °F