Search Results
Filter Your Search
Category Group
Shop by Category
Parback® backup ring with a curved cross-section.
Parbaks are contoured on one face to minimize distortion of the o-ring when under pressure. Parbaks should be installed with the contoured face against the o-ring, but reversal does no harm.
90A Durometer | Buna-N Rubber Material | 3 3/4 in Nominal Inner Diameter | 1/8 in Cross Section | Backup Ring
Features
- Excellent extrusion resistance
- Easily stretched for installation
- Lubrication is enhanced by rubber which absorbs system fluid and does not plate out on rubbing surfaces
Solid Urethane backup ring with a flat cross-section.
95A Durometer | Urethane Material | 2 1/4 in Nominal Inner Diameter | 1/8 in Cross Section | Backup Ring
Features
- High strength and abrasion resistance
- Wide temperature range
- Chemical resistance
- Low friction
- Easy installation
MCPO-36 has a 36 mm diameter with Standard Chrome. The base material is 1045 Carbon Steel with a yield strength of 75,000 psi.
ASTM A108 is the most commonly used and economical grade of shafting for hydraulic cylinder components, blower shafts, and mandrels.
- Extremely smooth surface finish
- Excellent wear and corrosion resistance
- Good strength and impact properties
- Good machinability
- Reasonable weldability
- Fair response to normal heat treating and induction hardening practices
Packages longer than 44 inches may have additional freight charges.
| 1-14 | $5.18 |
| 15-29 | $3.45 |
| 30-89 | $2.59 |
| 90-134 | $2.30 |
| 135+ | $2.07 |
1 3/4 X 2 1/4 X 3/8 B-lip URE
Utilizing a sturdy metal case, these wipers are molded from the same high performance urethane used in our Heavy Duty U-seals. Built for severe service, these wipers are capable of surviving hostile environments.
92A Durometer | Urethane Material | 2 in Nominal Inner Diameter
Features
- Used in Heavy Duty U-seals
- Capable of surviving hostile environments
- Molded from the high performance urethane
HT-6500X6000 has a wall thickness of 0.25 in. The ID is 6 in and the OD is 6.5 in. The material is DOM 1026 Steel – ST52.3 and has been stress-relieved and annealed.
Packages longer than 44 inches may have additional freight charges.
| 1-14 | $8.55 |
| 15-59 | $7.47 |
| 60-89 | $6.63 |
| 90-119 | $5.98 |
| 120+ | $5.44 |
DUCT-5000 has a diameter of 5 in. The material is 65-45-12 Ductile Iron.
65-45-12 Ductile Iron is used to machine pistons, glands, caps, manifolds, rams, and valve bodies.
Ductile has higher machining speeds than steel and there is usually no need for deburring machined parts. The graphite flakes in the material act as a self-lubricant. Ductile can be flame or induction hardened as well as deep hardened.
Ductile bars are produced with sufficient stock on the outside diameter to ensure clean-up at the nominal dimension.
- Excellent machinability
- Optimal impact strengths
- Optimal fatigue properties
- Optimal electrical conductivity
- High magnetic permeability
Packages longer than 44 inches may have additional freight charges.
| 1-9 | $22.81 |
| 10-39 | $17.70 |
| 40+ | $14.51 |
HT-6750X6000 has a wall thickness of 0.375 in. The ID is 6 in and the OD is 6.75 in. The material is DOM 1026 Carbon Steel and has been stress-relieved and annealed.
Packages longer than 44 inches may have additional freight charges.
| 1-14 | $13.10 |
| 15-59 | $11.45 |
| 60-89 | $10.17 |
| 90+ | $9.16 |
O-rings as elastic loops that seal static and dynamic applications. They are used to seal the space between cylinders, pistons, pipes and tubes and can be made from various materials.
70 Durometer | Buna-N Rubber Material | 5/8 in Nominal Inner Diameter | 1/16 in Cross Section | O-Ring
Features
- Pressure range varies according to diametral clearance
- Temperature range of -40 °F to -240 °F
