Search Results
Filter Your Search
Category Group
Shop by Category
Parback® backup ring with a curved cross-section.
Parbaks are contoured on one face to minimize distortion of the o-ring when under pressure. Parbaks should be installed with the contoured face against the o-ring, but reversal does no harm.
90A Durometer | Buna-N Rubber Material | 3 3/4 in Nominal Inner Diameter | 1/8 in Cross Section | Backup Ring
Features
- Excellent extrusion resistance
- Easily stretched for installation
- Lubrication is enhanced by rubber which absorbs system fluid and does not plate out on rubbing surfaces
Solid Urethane backup ring with a flat cross-section.
95A Durometer | Urethane Material | 2 1/4 in Nominal Inner Diameter | 1/8 in Cross Section | Backup Ring
Features
- High strength and abrasion resistance
- Wide temperature range
- Chemical resistance
- Low friction
- Easy installation
3 in induction hardened chrome shafting. The base material is 1045/1050 Carbon Steel with 0.0005 in (0.0127mm minimum)-thick chrome plating and a case depth of 0.05 in (1.27 mm).
Induction Hardened Chrome is typically used in abrasive envrionments where the cylinder is exposed to rocks or heavy debris. Also used to machine clevis pins.
- Greater strength
- Better resistance to mechanical damage
Packages longer than 44 inches may have additional freight charges.
| 1-29 | $16.80 |
| 30-59 | $12.01 |
| 60-119 | $9.32 |
| 120-287 | $8.40 |
| 288+ | $7.64 |
80mm induction hardened chrome shafting. The base material is 1045/1050 Carbon Steel with 0.0005 in (0.0127mm minimum)-thick chrome plating and a case depth of 0.05 in (1.27 mm).
Induction Hardened Chrome is typically used in abrasive envrionments where the cylinder is exposed to rocks or heavy debris. Also used to machine clevis pins.
- Greater strength
- Better resistance to mechanical damage
Packages longer than 44 inches may have additional freight charges.
| 1-29 | $16.80 |
| 30-59 | $12.01 |
| 60-119 | $9.32 |
| 120-287 | $8.40 |
| 288+ | $7.64 |
Utilizing a sturdy metal case, these wipers are molded from the same high performance urethane used in our Heavy Duty U-seals. Built for severe service, these wipers are capable of surviving hostile environments.
92A Durometer | Urethane Material | 2 in Nominal Inner Diameter
Features
- Used in Heavy Duty U-seals
- Capable of surviving hostile environments
- Molded from the high performance urethane
MCPO-36 has a 36 mm diameter with Standard Chrome. The base material is 1045 Carbon Steel with a yield strength of 75,000 psi.
ASTM A108 is the most commonly used and economical grade of shafting for hydraulic cylinder components, blower shafts, and mandrels.
- Extremely smooth surface finish
- Excellent wear and corrosion resistance
- Good strength and impact properties
- Good machinability
- Reasonable weldability
- Fair response to normal heat treating and induction hardening practices
Packages longer than 44 inches may have additional freight charges.
| 1-14 | $5.18 |
| 15-29 | $3.45 |
| 30-89 | $2.59 |
| 90-134 | $2.30 |
| 135+ | $2.07 |
1 3/4 X 2 1/4 X 3/8 B-lip URE
HT-6500X6000 has a wall thickness of 0.25 in. The ID is 6 in and the OD is 6.5 in. The material is DOM 1026 Steel – ST52.3 and has been stress-relieved and annealed.
Packages longer than 44 inches may have additional freight charges.
| 1-14 | $8.55 |
| 15-59 | $7.47 |
| 60-89 | $6.63 |
| 90-119 | $5.98 |
| 120+ | $5.44 |
HT-6750X6000 has a wall thickness of 0.375 in. The ID is 6 in and the OD is 6.75 in. The material is DOM 1026 Carbon Steel and has been stress-relieved and annealed.
Packages longer than 44 inches may have additional freight charges.
| 1-14 | $13.10 |
| 15-59 | $11.45 |
| 60-89 | $10.17 |
| 90+ | $9.16 |
