Search Results

CPO-0375 has a 0.375 in diameter with Standard Chrome. The base material is 1045 Carbon Steel with a yield strength of 75,000 psi.

ASTM A108 is the most commonly used and economical grade of shafting for hydraulic cylinder components, blower shafts, and mandrels.

• Extremely smooth surface finish
• Excellent wear and corrosion resistance
• Good strength and impact properties
• Good machinability
• Reasonable weldability
• Fair response to normal heat treating and induction hardening practices

Packages longer than 44 inches may have additional freight charges.

AN wipers are ideal for light duty and pneumatic applications. Its main purpose is to prevent dirt and contaminants from entering the hydraulic or pneumatic systems. Suffix “SH” designates slotted heel design, “V” designates fluorocarbon material, and “B” designates carboxilated nitrile material.

90A Durometer | Urethane Material | 2 in Nominal Inner Diameter

Features

• Flexible, snap-in design for easy installation into closed housings
• Low compression set

1.375 in induction hardened chrome shafting. The base material is 1045/1050 Carbon Steel with 0.0005 in (0.0127mm minimum)-thick chrome plating and a case depth of 0.05 in (1.27 mm).

Induction Hardened Chrome is typically used in abrasive envrionments where the cylinder is exposed to rocks or heavy debris. Also used to machine clevis pins.

• Greater strength
• Better resistance to mechanical damage

Packages longer than 44 inches may have additional freight charges.

Parback® backup ring with a curved cross-section.

Parbaks are contoured on one face to minimize distortion of the o-ring when under pressure. Parbaks should be installed with the contoured face against the o-ring, but reversal does no harm.

90A Durometer | Buna-N Rubber Material | 3 3/4 in Nominal Inner Diameter | 1/8 in Cross Section | Backup Ring

Features

• Excellent extrusion resistance
• Easily stretched for installation
• Lubrication is enhanced by rubber which absorbs system fluid and does not plate out on rubbing surfaces

Solid Urethane backup ring with a flat cross-section.

95A Durometer | Urethane Material | 2 1/4 in Nominal Inner Diameter | 1/8 in Cross Section | Backup Ring

Features

• High strength and abrasion resistance
• Wide temperature range
• Chemical resistance
• Low friction
• Easy installation

1 3/4 X 2 1/4 X 3/8 B-lip URE

Utilizing a sturdy metal case, these wipers are molded from the same high performance urethane used in our Heavy Duty U-seals. Built for severe service, these wipers are capable of surviving hostile environments.

92A Durometer | Urethane Material | 2 in Nominal Inner Diameter

Features

• Used in Heavy Duty U-seals
• Capable of surviving hostile environments
• Molded from the high performance urethane

HT-6500X6000 has a wall thickness of 0.25 in. The ID is 6 in and the OD is 6.5 in. The material is DOM 1026 Steel – ST52.3 and has been stress-relieved and annealed.

Packages longer than 44 inches may have additional freight charges.

DUCT-5000 has a diameter of 5 in. The material is 65-45-12 Ductile Iron.

65-45-12 Ductile Iron is used to machine pistons, glands, caps, manifolds, rams, and valve bodies.

Ductile has higher machining speeds than steel and there is usually no need for deburring machined parts. The graphite flakes in the material act as a self-lubricant. Ductile can be flame or induction hardened as well as deep hardened.

Ductile bars are produced with sufficient stock on the outside diameter to ensure clean-up at the nominal dimension.

• Excellent machinability
• Optimal impact strengths
• Optimal fatigue properties
• Optimal electrical conductivity
• High magnetic permeability

Packages longer than 44 inches may have additional freight charges.

HT-6750X6000 has a wall thickness of 0.375 in. The ID is 6 in and the OD is 6.75 in. The material is DOM 1026 Carbon Steel and has been stress-relieved and annealed.

Packages longer than 44 inches may have additional freight charges.