Snap-in Wipers for Sale | CRC Distribution

AN wipers are ideal for light duty and pneumatic applications. Its main purpose is to prevent dirt and contaminants from entering the hydraulic or pneumatic systems.

AN wipers will retrofit into glands prescribed in MS-33675 for corresponding dash numbers of MS-28776.

• Flexible, snap-in design for easy installation into closed housings
• Low compression set

Suffix “V” designates fluorocarbon material,“N” designates nitrile material, and “HT” designates high temperature urethane.

90A Durometer | Urethane Material | 2 1/2 in Nominal Inner Diameter

Features

• Urethane Wiper Ring
• Min. Temperature Range of ‘-40 °F; N: -40°; V: -20 °F; HT: -40 °F
• Max. Temperature Range of 200 °F; N: 225 °F; V: 350 °F; HT: 225 °F

Suffix “V” designates fluorocarbon material,“N” designates nitrile material, and “HT” designates high temperature urethane.

90A Durometer | Urethane Material | 8 in Nominal Inner Diameter

Features

• Urethane Wiper Ring
• Min. Temperature Range of ‘-40 °F; N: -40°; V: -20 °F; HT: -40 °F
• Max. Temperature Range of 200 °F; N: 225 °F; V: 350 °F; HT: 225 °F

RW-90URE-35×43×5

The Hallite 38 single-lipped polyester wiper/scraper is designed to fit metric housings including those of ISO 6195A. Suitable for heavy duty applications.

The proportions of the wiping lip ensure that contact is maintained with the surface of the rod to remove heavily deposited containments such as mud and ice.

The outside diameter of the wiper incorporates a crush lip to provide an interference fit with the housing. This feature helps prevent contamination from entering the groove.

The Hallite 38 wiper is molded in a polyester-based material to provide a tough, abrasionresistant wiper for the difficult conditions usually found in mining or earth moving applications.

• Crush lip design provides effective seal on housing
• Ribs relieve pressure and improve stability
• Effective scraping lip to scrape off heavily deposited containments including ice

A wide range of ST wipers are now offered in the slotted heel design. The slots in the heel allow excess hydraulic fluid to bypass the wiper, preventing wiper blowout.

90A Durometer | Urethane Material | 3/4 in Nominal Inner Diameter

Features

• Slotted heel design
• Slots in the heel allow excess hydraulic fluid to bypass the wiper

Wipers are installed in hydraulic cylinders to prevent dirt, dust, and moisture from entering the cylinder as they retract back into the system. A hydraulic wiper prevents contamination that could damage wear rings, seals, and other cylinder components.

90A Durometer | Urethane Material | 1 1/4 in Nominal Inner Diameter

Features

• Installed in hydraulic cylinders to prevent dirt, dust, and moistures
• Hydraulic wiper prevents contamination that could damage wear rings, seals, and other cylinder components

AN wipers are ideal for light duty and pneumatic applications. Its main purpose is to prevent dirt and contaminants from entering the hydraulic or pneumatic systems. Suffix “SH” designates slotted heel design, “V” designates fluorocarbon material, and “B” designates carboxilated nitrile material.

90A Durometer | Urethane Material | 2 1/8 in Nominal Inner Diameter

Features

• Flexible, snap-in design for easy installation into closed housings
• Low compression set

AN wipers are ideal for light duty and pneumatic applications. Its main purpose is to prevent dirt and contaminants from entering the hydraulic or pneumatic systems. Suffix “SH” designates slotted heel design, “V” designates fluorocarbon material, and “B” designates carboxilated nitrile material.

90A Durometer | Fluorocarbon Material | 4 in Nominal Inner Diameter

Features

• Flexible, snap-in design for easy installation into closed housings
• Low compression set

RW-95URE-45×53×5